Threadlockers

Permatex Medium Strength Threadlocker Blue Gel

$29.50$29.52· 10 g Gel Twist applicator

Part no. PX-24010 · Permatex part no. 24010 · price in CAD

Special order — not on our shelf. Order it and we bring it in, then call you with timing. Shipping AB/SK/MB $30 · ON/QC $40 · NT $50 (base FREE over $150).

100% genuine. 100% genuine Permatex, from authorized North American distribution.

A medium-strength threadlocker in a no-drip gel, dispensed from a twist-dial Gel Twist applicator without drips or mess and suited to vertical applications. It locks and seals nuts and bolts against vibration loosening and comes apart with standard hand tools. Permatex cites Mil-S-46163A, Type II, Grade N for it, with a temperature range of -54°C to 150°C (-65°F to 300°F).

Permatex’s Medium-Strength Threadlocker Blue is ideal for all nut and bolt applications 1/4″ to 3/4″ (6mm to 20mm). Threadlocker Blue eliminates need for stocking expensive lock nuts and lock washers and locks and seals while preventing parts loosening due to vibration. Protects threads from corrosion. Threadlocker BLUE is easily removable with hand tools for easy disassembly. The Gel formula provides “liquid-reliability” without drips, globs, mess or waste and is available in convenient dispensing systems: choose GEL TWIST® pin-point applicator or the GEL SQUEEZE® applicator.

✓All purpose, medium strength threadlocker
✓Ideal for all nut and bolt applications 1/4" to 3/4" (6mm to 20mm)
✓Locks and seals while preventing parts loosening due to vibration
✓Removable with hand tools for disassembly
✓Gel formula provides "liquid reliability" without drips, globs, mess or waste

Size

30-day returns · Secure Stripe checkout · 100% genuine · (780) 482-2424

⚠ Safety warnings

NOTE: Permatex Threadlocker Gel should not be used on plastic fittings. Do not use on food contact surfaces. Avoid food contamination during use and storage.
Avoid direct contact of tip to metal surface. *If contact occurs, expose 1/16″ of material and wipe off with a clean towel.
If unused gel contacts metal threads, do not retract threadlocker back into the tube. Wipe off with a clean towel.
This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials.
SDS: Danger. Causes skin irritation. Causes serious eye irritation. May cause cancer. May cause damage to organs through prolonged or repeated exposure.
SDS: Contains CUMENE HYDROPEROXIDE; CUMENE; TITANIUM DIOXIDE
California Proposition 65: WARNING Cancer.

Safety data sheet (SDS) →

Specifications & Approvals

(Mil-S-46163A, Type II, Grade N), NSF Nonfood Components Program Listed (P1) (135871), Temperature range: -65°F to 300°F (-54°C to 150°C), Chemical Type: Anaerobic Dimethacrylate Ester, Appearance: Opaque Blue Fluorescent Gel, Specific Gravity: 1.15, Flash Point (TCC), F (C): >200 (>93), Breakaway Torque, Nm, (in.lbs): 13 (115); Prevail Torque, Nm (in.lbs): 6 (53) (After 24 hr at 72F on 3/8-16 steel Grade 8 Nuts and Grade 5 bolts), A 3/8-16 steel nut and bolt assembly will fixture in 5 minutes using a primer, while fixturing will occur in 20 minutes without a primer. Full cure in 24 hours for both procedures, Full cure is attainable in 24 hours at room temperature, 22C (72F), or 1 hour at 93C (200F), For Disassembly 1. Remove with standard hand tools. 2. In the rare instance where hand tools do not work, because of excessive engagement length, apply localized heat to nut or bolt to approximately 450F (232C). Disassemble while hot

Recommended for vehicles requiring

Valve cover bolts, Water pump bolts, Oil pan bolts, Drive shaft bolts, Rocker arm adjustment nuts, Carburetor studs, Vertical applications, Belt tensioner bolts, pulley bolts, cup and core plugs, fan hub bolts, starter and alternator mounting bolts, intake manifold bolts, axle cover screws, disc brake caliper bolts

Treat rate

Turn dial to expose 1/8″ to 1/4″ of material beyond tip. Apply threadlocker to leading edge of male fitting, covering 5 to 6 threads. Note: First time use may require 4 to 5 full turns of the dial before material appears in the tip.

Common questions

Is this genuine Permatex Medium Strength Threadlocker Blue Gel?

Yes. 100% genuine Permatex, from authorized North American distribution. Everything we sell is genuine product — never grey-market.

Can I get it shipped or pick it up in Edmonton?

Both. Choose ship-to-me for delivery (AB/SK/MB $30 · ON/QC $40 · NT $50, base rate free over $150), or select pickup at checkout and collect it at our Edmonton shop.

Not sure this is the right threadlockers for your vehicle?

Check your owner's manual for the required specification or call our Edmonton team at (780) 482-2424 and we'll match the right product to your vehicle.